Static submerged media sump filters are simply sumps filled with both water and a biomedia through which the water flows. Most sump filters in the hobby are static submerged media sumps. These are like all submerged media filters in that the load of fish they can successfully filter is dependent on the media that one fills them with.
Media in a Submerged Sump Filter
Filter biomedia vary by the amount of effective surface area they give for beneficial bacteria to grow on. Note the term “effective” is very important. Many media suppliers report their surface area as what a nitrogen molecule can get too. Since a nitrogen molecule is a billion times smaller than any beneficial bacteria this is VERY misleading. The square feet of surface area per cubic foot of biomedia (ft2/ft3) actually available for colonization by beneficial bacteria is:
|Cubic inches to get 100ft²
|Fluidized K1 media
(60% loading in
|30 PPI foam in
canister or sump
|30 PPI foam
|30 PPI foam air
|Plastic pot scrubbers
|Static K1 media
|20 PPI foam in
canister or sump
|20 PPI foam
|20 PPI foam air
|Aquarium gravel in
canister or sump
|Blue Matala pads
|1/8 inch garden
pumice or perlite
|1/2 inch lava rock
|Cubic inches to get 5ft² = (5/E.A.)x1,728 100ft²=(100/E.A.x1,728)
Now a simple illustration is in order. Elsewhere we establish that fish are very healthy and well taken care of by a biofilter media which has very roughly 100 square foot of biomedia surface area per pound of fish. And very roughly 5.5 five-inch fish are in a pound of fish. A typical 40-gallon sump might have 24 gallons of submerged biomedia in it, or 3.2 cubic feet.
So foam in the submerged biomedia sump will support 3.2 x 400/100 or 12.8 pounds of fish or and astonishing 70 five-inch fish. Matrix, Biohome or ceramic rings in the submerged media will support 3.2 x 30/100 or 1 pound of fish or 6 five-inch fish. This is really a very astonishing calculation all sump owners should do.
Note that for reasons we will delve into under fluidized bed sumps a 40-gallon fluidized bed filled with 3.2 cubic feet of 60% K1 media and properly circulating with air will filter the water and keep in excellent health an astonishing 104 five-inch fish.
Design of a Submerged Sump Filter
The simplest design for a static submerged media sump is:
Other submerged setups are shown below:
Many commercial filter sumps are designed for saltwater aquariums and have protein skimmers and refugiums. These are unnecessary in a freshwater sump filter.
Filter sumps are customized in a hundred variations. Every aquarium owner has their own opinion as to the best filter sump design. That’s the nature of an “aquarium geek”.
Some have complained that if the mechanical filtration media becomes clogged the filter sump will overflow onto the floor. There are some small commercial units which can do this. This is a defective design. All good filter sumps are designed so that a clogged mechanical filter will only result in water pouring over into another part of the sump, bypassing some or all the filtration media.
There are some sump filter designs where the mechanical filtration (polyester pads) is after the biological filtration. There are also many sumps where the biomedia only fill a small portion of the sump. These are very inefficient designs.
Most sump users have bags of media in the sump which have four or more types of media in the bags (one YouTube presenter had eight different types of media!). Apparently, they feel each biomedia will have an advantage. All biomedia do the same thing, they just do it with varying degrees of success. This use of a large variety of media is just somewhat humorous but EVERYONE does it.
This sump has eight types.
Note how the chambers with the K1 are only partially filled with media in this sump. This is to make this chamber a fluidized bed. This is the best type of filter to use by far. But the chamber should be filled with K1 at a 60% level. This looks to be only 20% or so. This flow is down-up three times though six chambers. The small final two chambers are where the pump is located. So there is a sizable danger that evaporation will cause a dry pump failure with this design.
Sumps in More Depth
For more information on other types of sumps click on these links:
A variation of the static sump designs above is a very attractive method of filtration. It is a “foam sump” that is very simple in design and in operation. The article about these types of sumps is:
Note that many beginners are concerned about how to flow the water to a sump. The common refrain is “my aquarium isn’t drilled, how does the water get to the sump?” Click on this link to get some ideas:
Source: Aquariumscience.org – David Bogert